MARMORESIN SHOWER TRAY

What are the benefits of a marmoresin shower tray?

✓ Class 3 non-slip surface, for greater safety against falling;

✓ antibacterial, thanks to the sanitary GelCoat coating;

✓ extraordinary strength and durability over time;

✓ pleasant-to-the-touch surface;

✓ minimum thickness, between 2.5 cm and 3 cm;

✓ stain resistance and low maintenance required;

✓ installation on top of or flush with the floor;

✓ adaptable to every situation and customised cutting option;

✓ natural stone effect, which gives a truly unique appearance.

The Marmoresin shower tray by Coprimuro Srl is very strong but at the same time incredibly lightweight.

Some examples? A shower tray with dimensions 80×80 weighs only 29 kg…while a shower tray 80×140 weighs about 52 kg.

All the products have a modern design, with a stone-effect surface which is naturally non-slip (class 3). The surface also has antibacterial properties, as it is coated with a special sanitary GelCoat.

For cutting, dry or wet diamond discs are required.

To install the shower trays, the screed must be waterproofed.
The shower trays are installed on self-leveled compact screed using specific adhesives (such as COPRILASTIK supplied by us).

To clean the shower tray, use only neutral products; do not use acid products, (anti-limescale or abrasive products) as they may dull the surface.

If you would like more details about our Marmoresin shower trays, please contact us without obligation by sending your request on the form at the bottom of the page.

Before installing, make sure the shower tray is perfectly flat and in the case of slight curvatures, resulting from the elasticity of the materials, place the tray on a level surface and keep it there for about 4 hours, after which check that the shower tray is flat again.

To install using a spirit level, make sure the shower tray is level before spreading the adhesive.

1. Prepare the screed substrate and make sure the surface is smooth, leaving the necessary traces for the siphon trap and the drainpipes.

2. Install the drainpipes and siphon trap of the shower tray, making sure that the system is hydraulically sealed. Fill the traces with anti-shrinkage mortar making sure that the pipes do not protrude beyond the screed surface.

NOTE: To prevent the infiltration of moisture, it is advisable to prepare the bottom and walls with a layer of insulating product. Spread the entire bottom of the shower tray with a double layer of specific CoprilastiK adhesive or similar supplied by coprimuro.net.

3. Place the shower tray in the previously indicated position, making sure that the drain hole coincides with the previously installed siphon trap. Tighten the lock ring nut of the drain. Place the metal grille in the appropriate position on the shower tray.

INSTALLATION FLUSH WITH FLOOR

1. Prepare the screed substrate making sure that the surface is smooth and leaving the necessary traces for the siphon trap and drainpipe allocation.

2. Install the drainpipes and siphon trap of the shower tray making sure that the system is hydraulically sealed. Fill the traces with anti-shrinkage mortar making sure that the pipes do not protrude beyond the screed surface.

NOTE: To prevent the infiltration of moisture, it is advisable to prepare the bottom and walls with an insulating product. Spread the entire bottom of the shower tray with a double layer of specific adhesive.

3. Place the shower tray in the previously prepared seat, taking care to make the drain hole coincide with the previously installed siphon trap. Tighten the locking ring of the drain. Place the metal grille in the appropriate position on the shower tray.

What is the shower tray glued on with?
With our certified Coprilastik glue.

Can the shower tray be cut?
Yes of course, but not more than 10cm on each side.

Does the shower tray have a smooth surface?
No, its surface is similar to the prized effect of slated stone.

Is it non-slip?
It has a non-slip effect but, at an extra charge, antiskid treatment is available which certifies barefoot walking from classes R4 to R13 DIN 51130 and classes A/B/C/ DIN 51097.

NOTE: this treatment is carried out in our workshops and is followed by specific certification.

Is the drain in the shower tray included?
Yes, it comes together with the shower tray but at a separate cost.